Insulation data sheets: what to compare before buying

Structural Work
·
Joinery
·
Decoration
·
Consultancy
·
3D Design
·
Interior Design
·
Construction
·
Full Renovations
·
Architecture
·
Engineering
·
Demolition
·
Painting and Finishes
·
Electrical and Plumbing
·
Wall and Floor Finishes
Renovation wall detail with thermal insulation and window reveal finishing

To choose thermal insulation properly, start by comparing declared thermal conductivity, the thickness you can accommodate and the performance required at the installation point. Products that look similar can perform very differently in an internal wall, roof or floor. A data sheet should confirm the complete choice: material, declared performance, application limits, compatibility with the existing structure and the documents that should accompany the order.

Contents

  1. Start with the location: walls, roofs and floors have different demands
  2. What lambda means, and why a lower figure matters
  3. Thickness and thermal resistance: compare the assembly, not only the board
  4. Moisture, vapour and water: do not conceal the cause with insulation
  5. Fire behaviour, compressive strength and acoustics: read for the intended use
  6. Documents and installation: what to confirm before the wall is closed

Start with the location: walls, roofs and floors have different demands

Do not start with a brand or price per square metre. Define the part of the building envelope and the problem you need to address: winter cold, summer overheating, noise, condensation on an external wall or heat loss through the roof. ADENE describes roof insulation as a more specific intervention requiring particular technical skills, which is a useful warning against improvised work in lofts and roofs.

In Lisbon, a north-facing wall may need careful assessment of condensation risk when insulation is added internally; a roof exposed to strong sun also needs summer-heat control; and a floor above a garage or basement needs a solution suited to the substrate and available build-up. Before requesting quotations, record:

  • the building element to be insulated and its known construction;
  • available thickness without obstructing doors, shutters, sockets or furniture;
  • damp, leaks or cracks that must be resolved first;
  • the final finish and loads the assembly will need to carry.

For context on insulation and household comfort, see ADENE’s action plan on reducing heat losses.

What lambda means, and why a lower figure matters

The symbol λ, read as “lambda”, is declared thermal conductivity. Put simply, it indicates how readily heat moves through a material: the lower the figure, the less heat it transmits at the same thickness. Do not compare figures taken from packaging without checking that they refer to the same declared conditions and product type.

Lambda does not select insulation on its own. Two materials with similar figures may behave differently when exposed to water, compression, fire or installation on uneven surfaces. Mineral wool may suit a cavity or lightweight frame; a rigid board may be more appropriate where dimensional stability and compressive strength are needed. Cork may be suitable in certain assemblies, provided thickness, system and detailing are compatible.

Ask for the data sheet for the exact product going into the work, rather than a generic range document. In recent public schemes, technical documents were used to demonstrate the conductivity of insulation installed in walls and roofs, including a 0.065 W/(m.ºC) threshold for eligible solutions in that context. Read the requirements in the Portuguese Official Gazette notice on insulation solutions.

Thickness and thermal resistance: compare the assembly, not only the board

A useful comparison combines lambda and thickness. Thermal resistance increases with thickness and decreases as a material conducts more heat. A thinner board with a favourable lambda can therefore approach the performance of a thicker alternative; it still does not solve every construction detail automatically.

Ask a direct question when reviewing quotations: “What thickness will be installed once adhesives, framing, service voids and finishes are included?” On an internal wall, every centimetre can affect reveals, skirtings, radiators or furniture. In a roof, the issue includes ventilation, maintenance access and continuity of insulation. A layer interrupted by metal framing, shutter boxes or poorly finished junctions leaves colder areas and reduces the expected benefit.

Do not accept a quotation described only as “X centimetres of insulation”. Request the material, declared lambda, nominal thickness, thermal resistance of the assembly and drawings of junctions. If the work includes windows, coordinate the interfaces: window detailing can determine whether thermal bridges appear around reveals.

Useful questions when comparing two insulation proposals
Data-sheet or proposal itemWhat to checkWhy it matters
Declared lambdaUnit, exact product and declared conditionAllows a like-for-like comparison of material conductivity
Installed thicknessFinal thickness, including system and finishShows the space actually occupied and affects thermal resistance
Intended applicationWall, roof, floor or wet areaAvoids using a product outside its designed conditions
DocumentationData sheet, instructions and applicable declarationHelps control delivery and installation
Thermal insulation samples and technical drawings on a renovation work table

Moisture, vapour and water: do not conceal the cause with insulation

Insulation does not repair a leak. Before closing an internal lining, establish whether water is entering through the façade, roof, a crack, pipework or recurring condensation. Adding an internal system over a damp substrate can trap moisture in the wall and make the original cause harder to identify.

Ask for the assembly to identify every layer clearly: existing substrate, levelling, adhesive or framing, insulation, any vapour-control layer, service void and lining. These layers are not interchangeable. Their position depends on the existing wall, exposure, room ventilation and insulation type. Cutting or puncturing a control layer without planned seals can compromise the whole assembly.

There are also important differences between products exposed to liquid water, ground moisture or indoor vapour alone. In shower rooms, kitchens, basements and low-level floors, do not choose by habit. Check water absorption, waterproofing requirements and compatibility with the planned mortars, boards or finishes. Adding or replacing envelope insulation is among the measures listed in ADENE’s energy-efficiency resources; it works best when the moisture source has already been diagnosed.

Fire behaviour, compressive strength and acoustics: read for the intended use

Not every part of a data sheet carries the same weight in every project. In a lightweight partition between rooms, acoustics and fire behaviour can be decisive. In a floor below screed or a rigid finish, compressive strength also matters. On a façade or roof, the full system, fixings and fire-compartmentation details may be as important as the insulation board itself.

Avoid turning a single characteristic into a broad conclusion. A material with good fire performance still needs a properly detailed assembly; a dense product does not automatically provide sufficient acoustic insulation; a compression-resistant board may be unsuitable for an uneven or curved internal wall. Read the installation instructions and confirm that the manufacturer permits that specific use.

Where work involves ETICS, heavy cladding, façade changes or common building parts, do not mix components from different systems without technical confirmation. The Official Gazette notice mentioned above states that, for ETICS, insulation-related requirements concern the insulation board, while also referring installation to good-practice rules. If external work includes water, drains and junctions, read our guide to waterproofing a balcony before replacing the floor.

Documents and installation: what to confirm before the wall is closed

Before appointing a contractor, keep the data sheet, approved quotation, drawings of critical junctions and installation instructions. At delivery, check that the material received matches the agreed specification: thickness, reference, system, accessories and quantity. Photographs taken before the lining is closed can help locate fixings, service voids and future penetrations.

Construction products covered by European rules must be accompanied by the applicable documentation. In Portugal, the declaration of performance must be provided in Portuguese, and product instructions and safety information must be supplied in Portuguese. These requirements appear in the Portuguese rules implementing the Construction Products Regulation.

  1. Request the data sheet and applicable declaration before ordering.
  2. Confirm compatibility between insulation, adhesive, fixings, membranes and finish.
  3. Check continuity at corners, reveals, shutter boxes and service penetrations.
  4. Photograph layers and junctions before walls or ceilings are closed.

If there is persistent damp, significant cracking, façade or roof work, or an assembly affecting fire behaviour, seek technical assessment rather than deciding from a catalogue alone. For a well-documented interior project, see how to organise handover, warranties and defect records in a renovation.

Key takeaways

  • Compare lambda and thickness together; neither figure is enough by itself.
  • Choose the product for its installation location, moisture conditions and planned finish.
  • Request data sheets, instructions and documentation before materials are ordered.
  • Photograph hidden layers and junctions before walls or ceilings are closed.

If you are preparing a Lisbon renovation, gather the material data sheets and ask Obra Lisboa for a proposal that identifies the assembly, junctions and execution scope before work begins.

Sources and further reading

Editorial image; it does not depict an Obra Lisboa project.

Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
Let's Work Together
·
ObraLisboa - Construção e Remodelação de propriedades
let's create
together