
Install an irrigation controller in a dry, accessible place away from direct sun, and treat it as part of a water and electrical installation that needs regular care. At a Lisbon house, that decision helps prevent flooded boxes, watering at unhelpful times and faults that only emerge when the garden needs water most. Before buying equipment, define the zones, confirm the available pressure and choose pipe runs that can be checked without lifting paving.
Contents
A controller cannot compensate for a poorly divided network. First, draw the garden and group plants with similar needs: lawn, exposed pots, newly planted hedges, established beds and trees should be able to run for different lengths of time. One zone for everything usually means too much water in one place and too little in another.
Also mark the water supply, filter, valves, inspection boxes and pipe runs near walls. A Portuguese official specification for irrigation systems favours pipework in planted areas and keeps it away from façades; it is not an automatic rule for every house, but it is a useful principle for avoiding difficult repairs and damp risks close to the building.
If trenches are open during renovation, add this information to a digital renovation folder, including the layout, photographs and equipment references.
The best location is a wall inside a storage room, ventilated garage or dry utility cupboard, close to the electrical supply and easy to reach when schedules need changing. Avoid putting the controller inside a buried valve box: it is exposed to condensation, soil, water and cramped access for checking connections.
If the controller must be outdoors, use an enclosure designed for that setting, fixed above the level of possible puddles and sheltered from driving rain. Its door should open without moving pots, furniture or garden tools. Leave enough cable slack for maintenance, without creating loose loops within reach of children, pets or garden equipment.
Do not conceal the controller behind fixed finishes simply to keep a wall visually clear. A small, well-ventilated technical cupboard is more useful than an invisible installation that requires dismantling finishes whenever a battery fails, a valve stops responding or irrigation needs to be isolated.
The power point needs to suit its location and be protected from splashes, leaks and physical damage. Do not power the system with permanent extension leads across the garden or from an indoor socket through an open window. If a new outdoor supply is needed, ask an electrician to confirm the circuit, protective devices and earthing before equipment is connected.
On the water side, provide a manual isolation valve before the solenoid-valve assembly and a filter that can be cleaned without dismantling the whole installation. If the house already has other outdoor electrical loads, keep identification clear. A simple isolation map is also useful in a leak; see how to prepare an electrical panel and test your home RCD without unsafe improvisation.

Do not copy a neighbour’s schedule or keep one programme all year. The 1991–2020 Lisbon/Tapada normals show hot, dry summers, with July and August among the months with least rainfall, while autumn and winter receive much more rain. Check the figures in the IPMA climate normals for Lisbon/Tapada and use them as context, rather than as an irrigation instruction for every plant.
Schedule watering early in the morning, when evaporation is lower and leaks or displaced emitters are easier to spot. Begin with moderate run times, observe how deeply the soil is wetted and adjust one zone at a time. A bed beside a sunny wall dries differently from an area shaded by mature trees.
After meaningful rainfall, temporarily suspend the programme and check the soil by hand a few centimetres below the surface. Green grass at the surface does not prove that roots received enough water; persistent puddles do not mean good irrigation either, but may point to poor drainage or excessive flow.
For pots, hedges and planted beds, drip irrigation delivers water close to the soil, with less wetting of walls, foliage and paths. Inspect emitters regularly: roots, limescale, soil and insects can change their output or block them. Sprinklers are more affected by wind and need their throw checked so they do not water windows, façades, pavements or a neighbour’s property.
A rain sensor can prevent unnecessary cycles, but it does not replace observation. Check that it is positioned where rainfall reaches it, without shelter from an eave, dense canopy or wall. Clean it before the watering season and test whether it actually interrupts the programme.
Avoid equipment that produces a fine mist near seating areas, especially if it remains unused for long periods. The Portuguese health authority guidance on Legionella prevention and control includes water-aerosol-generating systems among equipment that requires attention to maintenance. In a home garden, the cautious response is to use drip irrigation where appropriate, avoid stagnant water and clean or replace deteriorated components.
Carry out a short inspection at the start of spring and again before the wetter period. Open each zone separately, walk through the garden and look for jets outside their target, dry emitters, damaged lids, boxes full of soil and valves that do not close properly. Fix leaks and blockages first; only then change controller run times.
At the end of summer, reduce duration gradually and turn off zones that no longer need regular watering. Before a long absence, do not increase every setting as a precaution: first check the filter, pressure and soil condition. Keep a brief record of cleaning dates, replacement parts and programme changes.
Call a professional if pressure falls across several zones, the RCD trips, water reaches cables, valves remain open, moisture appears near the façade or a new electrical circuit is required. Those are signs to stop DIY work and diagnose the cause before hiding the problem beneath soil, bark mulch or paving.
Key takeaways
If irrigation is part of a house renovation, include zones, valves, power supply and maintenance access in the brief from the outset. Obra Lisboa can help coordinate those decisions with the remaining exterior and technical works.
Sources and further reading
Editorial image; it does not depict an Obra Lisboa project.
Privacidade e controlo
Usamos cookies essenciais para o funcionamento do site. Com a sua autorização, podemos também medir a utilização e os resultados dos anúncios. A medição de publicidade com a OpenAI usa referências técnicas, sem enviar nome, email, telefone ou mensagem do pedido. Pode aceitar, rejeitar ou gerir cada categoria. Consulte a Política de Privacidade e a Política de Cookies.
Necessários para segurança, navegação e memorização da sua escolha.
Ajuda a medir utilização e desempenho sem enviar dados de contacto.
Permite medir campanhas, incluindo anúncios no ChatGPT. Com a OpenAI, a medição usa referências técnicas para associar pedidos aos anúncios, sem enviar nome, email, telefone ou mensagem. É opcional e pode ser desativada a qualquer momento.