
You can replace a basin mixer tap at home when the isolation valves work properly, the connections are accessible and there is no corrosion, cracking or standing water inside the cabinet. It may look like a small job, yet one overtightened nut or twisted hose can cause a slow leak that is only noticed after the cabinet base has been damaged. Prepare the work, confirm the connection type and test patiently before returning the bathroom to normal use.
Contents
Start by looking closely at the existing tap without dismantling it. Check whether the basin has a single tap hole, whether the new tap includes flexible hoses, and whether the spout height leaves room to wash hands without throwing water beyond the bowl. In a low vanity, also make sure there is enough room to tighten the retaining nut underneath.
Photograph the space below the basin and note the apparent valve size, hose positions, basin thickness and distance to the wall. Do not choose a tall tap solely because it looks better: on a shallow basin, the stream may land too close to the front edge.
Efficiency matters as well. ADENE notes that a tap or shower with suitable features and flow can use substantially less water for the same purpose and comfort, so compare the flow regulator and aerator compatibility before choosing. See ADENE’s guidance on efficient water fittings.
Avoid shutting off the water only to find that a tool is missing. For a straightforward replacement, gather an adjustable spanner, a basin wrench or tap-nut tool, a shallow bucket, absorbent cloths, a torch and gloves. Keep dry kitchen paper or toilet tissue to reveal tiny drips at the joints during testing.
Do not use PTFE tape on flexible-hose nuts that seal with a flat washer: the internal washer, rather than the thread, provides the seal. Tape can prevent correct tightening and conceal a distorted washer. Put the plug in place or lay a cloth in the basin too, so that a nut cannot disappear down the waste.
If the vanity contains a socket, mirror transformer or lighting cables, isolate that circuit before working where a spill is possible. For a reminder about the limits of extension leads and adapters around wet areas, read when power strips stop being a safe solution.
Look for the two isolation valves beneath the basin: one for cold water and one for hot water. In correctly installed systems, isolation valves should be fitted on bathroom and kitchen distribution branches, as well as before equipment such as washing machines. This allows a local repair without shutting water off throughout the home. See the regulation published in Diário da República.
Do not attempt to operate the valve upstream of the meter, in the service cupboard or in the street. The regulations reserve operation of that valve to the water utility, firefighters or civil protection. The internal plumbing after the delivery point is generally the owner’s responsibility, including its upkeep. Read the framework in the regulation on building plumbing and public-network connections.

First loosen the flexible hoses at the isolation valves, holding the valve steady with a second spanner if the pipe starts to turn. Let residual water fall into the bucket. Then release the nut or fitting holding the tap below the basin. In older basins, limescale and corrosion can make this stage slow; do not apply sideways force to the ceramic.
Once the tap is out, clean the base of the basin with a damp cloth and dry it thoroughly. Remove old compound, silicone or limescale only from the seating surface. A base washer needs a clean, smooth surface; silicone around the tap is not a substitute for that washer and can make later inspection harder.
Inspect the inside of the cabinet. A swollen base, dark staining, heavily corroded pipes or a valve that turns on its pipe are reasons to postpone the replacement and call a plumber. It is better to repair an accessible defective connection now than to fit a new tap onto unstable pipework.
Insert the new tap with the washer specified by the manufacturer. Below the basin, fit the washer and mounting plate in the stated order and tighten until the tap no longer turns. Align the spout before final tightening; trying to correct it later can twist the hoses.
Start each flexible hose by hand, making sure the thread engages squarely. Only then tighten moderately with a spanner. Hoses should not have a sharp bend, rub on a metal edge or become taut when a drawer is opened. Connect hot water to its correct valve and cold water to the other; if you are unsure, follow the markings or the manufacturer’s instructions rather than assuming by position.
If this is part of a bathroom or kitchen renovation rather than a one-off repair, include taps, isolation valves and connections in the scope you request. This guide to requesting comparable renovation quotes helps turn technical details into items that can be checked.
Open the isolation valves slowly first, keeping the tap closed. Run dry paper around every joint: even the smallest drop will leave a mark. Then run cold water for one minute, close it, repeat with hot water and inspect again. Finally, run both supplies and check that the stream lands well inside the bowl and that the waste drains without splashing.
Check again after one hour and on the following day. Slow leaks often appear only after the pipework has warmed, cooled or experienced small movements in normal use. Keep the cabinet base dry and clear of boxes during this period so that any sign is visible early.
Stop and call a professional if a valve will not close, a thread is damaged, a concealed connection moves, pressure seems abnormal, the trap begins to leak or the repair requires altering fixed pipework. A new tap cannot solve a leak inside a wall or replace an isolation valve that has already stopped doing its job.
Key takeaways
If the tap is part of a wider renovation, include accessible isolation valves, connections and leak testing in the work scope. Speak to Obra Lisboa before finalising your equipment choices and sequencing the work.
Sources and further reading
Editorial image; it does not depict an Obra Lisboa project.
Privacidade e controlo
Usamos cookies essenciais para o funcionamento do site. Com a sua autorização, podemos também medir a utilização e os resultados dos anúncios. A medição de publicidade com a OpenAI usa referências técnicas, sem enviar nome, email, telefone ou mensagem do pedido. Pode aceitar, rejeitar ou gerir cada categoria. Consulte a Política de Privacidade e a Política de Cookies.
Necessários para segurança, navegação e memorização da sua escolha.
Ajuda a medir utilização e desempenho sem enviar dados de contacto.
Permite medir campanhas, incluindo anúncios no ChatGPT. Com a OpenAI, a medição usa referências técnicas para associar pedidos aos anúncios, sem enviar nome, email, telefone ou mensagem. É opcional e pode ser desativada a qualquer momento.