
A window that rubs, is hard to close or lets in draughts should be cleaned and inspected before you tighten screws or buy new seals. Many faults begin with dirty tracks, blocked drainage holes or distorted gaskets; others point to tired hardware, a misaligned sash or water ingress that DIY will not solve. The aim is to restore smooth closing without blocking ventilation or forcing parts that may break.
Contents
Open and close each sash slowly. Note the exact point where resistance occurs: at the start of travel, near the lower corner, when the sash meets the frame, or only when turning the handle. Sliding and hinged windows fail in different ways, so this basic diagnosis prevents random adjustments.
Photograph the closed opening from inside and outside, especially where there is damp, peeling paint or staining on the sill. Excess moisture encourages condensation and mould, so leaks and water run-off should be dealt with promptly, as stated in the Portuguese Directorate-General of Health guidance on indoor air.
First remove loose dust with a narrow vacuum nozzle or a soft brush. Then wipe with a lightly damp cloth and dry the area. On sliding windows, clean the full track, including corners where wind and rain leave sand. On hinged windows, clean the frame, hinge area and gasket without soaking the mechanism.
Do not push wire, drill bits or rigid tools into drainage holes: you may pierce an internal part or force debris into an inaccessible area. If water remains in the track after gentle cleaning, or appears indoors after rain, arrange a diagnosis. During a renovation, this check should also be coordinated with window and ventilation decisions rather than sealing every air path indiscriminately.
With the window open, run a finger along the gasket. Look for flattened, torn, sticky or loose sections. On sliding windows, inspect the brush seals: they should be continuous and make even contact, without folding into the track. Cleaning a gasket is reasonable; sticking new strips over a distorted seal rarely corrects a misaligned sash.
Use a simple paper test: place a sheet between sash and frame, close the window and pull gently. Repeat at several points. One isolated difference may indicate local wear; weak grip around the full perimeter needs a more careful assessment. This is not a certified air-tightness test.
The Portuguese Directorate-General of Health advises weatherstripping doors and windows to reduce cold-air entry and heat loss, while also advising that homes remain aired. In Lisbon, sealing a gap must not mean blocking grilles or removing the air renewal needed to manage moisture and pollutants. Read the DGS guidance for cold periods before choosing a sealing solution.

There is a practical boundary: you can check whether a visible screw is loose and tighten it carefully with the correct bit, without exceeding normal resistance. Do not turn adjustment screws unless you know what each one does, remove hinges while the sash is under load, or try to lift a heavy window alone. One wrong turn can worsen the contact, damage the hardware or shift the sash out of position.
Before making any adjustment, mark the starting position with painter’s tape and make only a small change. Test closing, opening and contact with the frame. If there is no immediate improvement, return to the original position. Do not use cooking oil, grease or random sprays on gaskets and mechanisms: they collect dirt and can damage materials.
For new, large or façade-integrated windows, consult the manufacturer’s instructions and call the installer. Portuguese rules require glazed-envelope components to be installed or renewed by qualified parties, following technical documentation and proper workmanship; see the technical rules for glazed building elements and ventilation.
A poorly adjusted window can be uncomfortable, yet an overly sealed home can also retain moisture, odours and carbon dioxide. In naturally ventilated homes, air should enter through main rooms and be extracted through service areas such as kitchens and bathrooms. This helps explain why grilles, air inlets and gaps intended for the system should not be covered.
If you feel cold air on a windy day only, first establish whether it comes from the window, shutter box, sill or a grille. If there is morning condensation on the glass, review ventilation habits, indoor clothes drying and steam extraction before blaming the frame. Indoor air quality includes ventilation, temperature, humidity and pollutants, according to the ADENE glossary.
Keep the routine straightforward: ventilate after cooking and showering, keep extraction areas working and dry water that gathers in tracks. For damp-weather decisions, see our guide to ventilating a Lisbon flat when it rains.
Call a professional if the sash visibly drops, touches the glass, has cracks, closes only with a bang, shows substantial corrosion in the hardware or lets water in after drainage has been cleaned. Do the same where the window forms part of a shared façade system, or where work involves replacing glass, altering profiles or changing the building’s external appearance.
A useful request for help starts with a short description: window type, approximate age, where it rubs, photographs, whether the problem occurs in rain or wind, and whether there are water marks. This helps distinguish maintenance, adjustment, gasket replacement and junction repairs. If the window is being dealt with during wider works, include it in the quotation request to avoid repeat work; see how to prepare a brief for comparable renovation quotations.
The intended result is simple: the sash moves without force, closes evenly, drains water outside and still supports ventilation designed for the home.
Key takeaways
If window work forms part of a Lisbon renovation, ask Obra Lisboa to include it in the existing-condition review and works scope before materials and trades are confirmed.
Sources and further reading
Editorial image; it does not depict an Obra Lisboa project.
Privacidade e controlo
Usamos cookies essenciais para o funcionamento do site. Com a sua autorização, podemos também medir a utilização e os resultados dos anúncios. A medição de publicidade com a OpenAI usa referências técnicas, sem enviar nome, email, telefone ou mensagem do pedido. Pode aceitar, rejeitar ou gerir cada categoria. Consulte a Política de Privacidade e a Política de Cookies.
Necessários para segurança, navegação e memorização da sua escolha.
Ajuda a medir utilização e desempenho sem enviar dados de contacto.
Permite medir campanhas, incluindo anúncios no ChatGPT. Com a OpenAI, a medição usa referências técnicas para associar pedidos aos anúncios, sem enviar nome, email, telefone ou mensagem. É opcional e pode ser desativada a qualquer momento.